如果您对该产品感兴趣的话,可以
产品名称:
CIT-03-04-50，YUKEN叶片泵参数
产品型号:
CIT-03-04-50
产品展商:
YUKEN
关注指数:418
产品文档:
无相关文档
简单介绍
CIT-03-04-50，YUKEN叶片泵参数
The pollution control of hydraulic oil, and maintain the pollution level within the NAS 12 level.
Note that if the PVL1 pump is started at a low speed of 950 r / min, the maximum fluid viscosity is limited to
The maximum permissible deviation is less than 0.1 mm (.004 in.) TIR and maximum allowable error
Less than 0.2 °.
CIT-03-04-50，YUKEN叶片泵参数
CIT-03-04-50，YUKEN叶片泵参数
的详细介绍
CIT-03-04-50，YUKEN叶片泵参数
企业QQ：2880626087
电话；
手机；（微信）
邮箱；@163.com
联系人；周彩云
地址：上海市嘉定区江桥嘉涌路99弄6号713室
1. Type of hydraulic oil
Oil base oil ........... U. Se R & O (rust and oxidation inhibitor) type oil or anti-wear type oil.
In addition, use a 100 mm (150 mesh) fuel tank filter on the suction
side and install a tank with a distance of more than 50 mm (2 inches).
200mm 2 / s (910SSU).
Description
3. Pollution control
(Equivalent to ISO VG-32 or 46)
Note: Only oil base oil can be used for hydraulic oil.
2. Recommended viscosity and oil temperature
The viscosity range is 20-400 mm 2 / s (100-1800 SSU).
, Directory number. EC-3001), or air is discharged by a slightly loose discharge side connection.
When starting, run the pump as intermittently as possible without load.
Use hydraulic oil that meets the recommended viscosity and oil temperature.
Refer to the "Hydraulic Oil" section above for fluid viscosity at start-up.
4. Other precautions
If you are using a PVL1 series single pump at speeds below 1200 r / min,
install the pump above the suction port
Use a flexible coupling as much as possible and avoid any stress generated by bending or thrust.
Hydraulic fluid contamination leads to pump failure and reduced pump life. adequate
Axis alignment
CIT-03-04-50，YUKEN叶片泵参数
If the pump is installed on top
The tank level is set below the oil level below 1.0 m (3.3 ft.).
Oil temperature at 0 / + 70 ° C (32 - 158 ° F)
So that the pump is easy to draw fluid at start-up.
3. Start the note
The pump may be difficult to draw fluid during initial operation or for a long period of rest.
In this case, the exhaust valve should be pre-installed on the discharge side (model number ST1004 - - 10)
2. Inhalation pressure
The suction pressure is set at -20 to +30 kPa (5.9 in.Hg to +4.3 PSIG) at the pump inlet.
In addition, use the suction pipe of the size shown in the dimension drawing.
CIT-03-04-50，YUKEN叶片泵参数
- 温馨提示：为规避购买风险，建议您在购买前务必确认供应商资质与产品质量。
- 免责申明：以上内容为注册会员自行发布，若信息的真实性、合法性存在争议，平台将会监督协助处理，欢迎举报
