产品[
DG5V-10-W-2A-E-M-W-H-10,威格士轴配流马达[产品打印页面]
]资料
如果您对该产品感兴趣的话,可以
产品名称:
DG5V-10-W-2A-E-M-W-H-10,威格士轴配流马达
产品型号:
DG5V-10-W-2A-E-M-W-H-10
产品展商:
威格士VICKERS
关注指数:493
产品文档:
无相关文档
简单介绍
DG5V-10-W-2A-E-M-W-H-10,威格士轴配流马达
伺服阀, SE3-02-220-002-10, SE3-02-40
5-002-10 零件和维修 English I-3054-S
SA4 系列, 两级伺服阀, SA4-03---1
, SA4-06---1 零件和维修 English I-3060-S
电子/放大器./电源,放大器, 电源补给,
DG5V-10-W-2A-E-M-W-H-10,威格士轴配流马达
的详细介绍
DG5V-10-W-2A-E-M-W-H-10,威格士轴配流马达
This manual provides service information for Eaton
Models 33 thru 64 Variable Pumps. Step by step
instructions for the complete disassembly, inspecti
on and reassembly of the pump are given. The following
recommendations should be followed to insure successful repairs:
· Most repairs require the removal of the pump from the vehicle.
· Clean the port areas thoroughly before disconnecting the hydraulic lines.
· Plug the pump ports and cover the open hydraulic lines immediately after they’re disconnected.
· Drain the oil and clean the exterior of the pump before making repairs.
· Wash all metal parts in clean solvent.
· Use compressed air to dry the parts. Do not wipe them dry with paper towels or cloth; Lint in a
· The compressed air should be filtered and moisture free.
· Always use new seals when reassembling hydraulic pumps.
· For replacement parts and ordering information refer to parts list 6-608.
· Lubricate the new rubber seals with a petroleum jelly like Vaseline before installation.
· Torque all bolts over gasketed joints, then repeat the torquing sequence to make-up for gasket
14 Pull the two check valves from the end cover; Hook
the short end of the pulling tool in one of the check valve
If the pulling tool is unavailable remove each check valve
by inserting a screw driver into the output port and prying
up on the bottom of the check valve.
Note: A detailed drawing of the check valve pulling tool
15 Remove the o-rings and back-up rings from the
11 Reposition the pump so the shaft is vertical and the
charge pump is on top. Stand the pump on two blocks
of wood as shown in figure 3.
12 Remove the four bolts that hold the charge pump to
the end cover, see figure 3. The two remaining bolts
hold the charge pump together.
Note: Information on charge pump repair is given in
13 Lift the charge pump from the end cover. Remove
the gasket and two dowel pins.
Note: Keep track of the dowel pins, see figures 3, 5,
and 8. There is a total of nine dowel pins in the pump. It
is a good idea to put them in a small box so they don’t
- 温馨提示：为规避购买风险，建议您在购买前务必确认供应商资质与产品质量。
- 免责申明：以上内容为注册会员自行发布，若信息的真实性、合法性存在争议，平台将会监督协助处理，欢迎举报
